noobks.blogg.se - How to install spark plugs on a 2007 suzuki gs500f

How to install spark plugs on a 2007 suzuki gs500f how to#
How to install spark plugs on a 2007 suzuki gs500f driver#

In the back of the purge valve, there's a connector. Disconnect that and slide that out of the way. This hose goes to the evap purge valve, so just push down on this lock. On the map sensor, we're going to do the same. Then, there's a little retainer right here.

Pull that lock and then push down on the tab. We'll disconnect this connector right here is a little lock. There's a little grommet on the backside here and just pull up on that just like that. With that loose I can just grab the snorkel right here.

I can use a straight blade screwdriver or an 8mm socket, extension, and ratchet. I want to loosen up this one clamp right here. Next thing, we I'm going to just slide this off right here, this hose, set that aside. It's a caged bolt, so we'll leave that there. If you don't have an electric one, you can use a regular ratchet. I'm going to use a 10mm socket and a electric ratchet. So I don't drop anything down into the oil, just put the cap back on.

I'm going to use a T30 socket, extension, and a ratchet. I can either leave that hung over like that or just leave that on the side like that. We're going to use a 10mm wrench to loosen this up. Now, the negative terminals on this side. There's two on this side and two on the other side and you can lift this up. You want to push down on these little lock tabs. When doing this job, it's a good idea to disconnect the battery. If you need these parts or other parts for your vehicle, click the link in the description, head over to.

How to install spark plugs on a 2007 suzuki gs500f how to#

In this video, I'm going to show you how to replace the spark plugs in this 2013 Cadillac SRX. Reconnect the battery negative cable and tighten it with a 10 mm wrench.Tighten the air filter and throttle body air box clamps.Reconnect the air box to front valve cover hose.Reinstall the air box onto the air filter and throttle body.

How to install spark plugs on a 2007 suzuki gs500f driver#

Reinstall the coolant line 10 mm bolts, the longer on the driver side.

Reconnect the throttle body electrical connector and retainer.

Reconnect the evap purge electrical connector.

Reinstall the 10 mm power steering hose bracket bolt.

Reconnect the intake plenum to rear valve cover hose.

Reconnect the MAP sensor electrical connector.

Reattach the wiring harness retainers to the driver side of the intake plenum.

Reinstall the insulation block push pin retainer.

Reinstall the 10 mm insulation block bolt.

Torque the six 13 mm intake bolts to 18 ft-lb in the specified order.

Wipe clean the gasket surfaces of the intake plenum.

Blow compressed air into the intake ports to clear out any debris.

Clean the gasket surfaces of the intake ports.

Remove the towels covering the intake ports.

Cover the intake ports to prevent debris falling inside.

Remove the six 10 13 mm intake plenum bolts.

Remove the two 10 mm bolts to move the cooling line crossing over the intake plenum.

Remove the 10 mm bolt to remove the insulation block.

Pry off the push pin retainer for the insulation block on the driver side of the engine.

Pry off the wiring retainers at the rear and driver side of the intake plenum.

Disconnect the brake booster vacuum hose.

Disconnect the rear valve cover to intake hose from the rear valve cover.

Remove the 10 mm bolt from the power steering hose bracket.

Disconnect the purge valve electrical connector.

Disconnect the MAP sensor electrical connector.Disconnect the throttle body electrical connector.Disconnect the air box from the air filter and throttle body to remove it.Loosen the air filter to air box clamp, and the air box to throttle body clamp.Disconnect he hose running from the air box to the front valve cover.Loosen the 10 mm bolt at the front of the air box.Disconnect the negative battery cable by loosening it with a 10 mm wrench.